 | | Re: Problem to send long messages from RCX to PC via com Hack
|
|
(...) Dear Matthew I have found the problem. It was in kernel\lnp-locical.c -> cheking the echo was the problem solution: echo OFF it is a rough solution, but it works changes 1) rx_handler(void) ... // echos of own bytes -> collision detection // (...) (16 years ago, 29-Jun-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Problem to send long messages from RCX to PC via com Hack
|
|
I don't know if this is would be of any help, as it uses a different approach, but I thought I'd pass it along anyway.... Bi-directional Bluetooth to IR translator - (URL) (PDF format: (URL) ) While this solution doesn't allow both the serial and IR (...) (16 years ago, 28-Jun-08, to lugnet.robotics.rcx.legos)
|
| |
| | Problem to send long messages from RCX to PC via com Hack
|
|
Hi, Once again i am back about RCX and BT-Connection. Receiving messages from the PC via BT to the RCX is OK. But if I send messages from the RCX to the PC with 4800 Baud i get only 4 Bytes. So I go back to 2400 Baud, forget BT and make a serial (...) (16 years ago, 10-Jun-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: RCX Serial Hardware Hack
|
|
Dear Claude (...) A: Thank you for finding the PDF. (...) A: I will check ( measure the Voltage on the IF LEDS) should be approx. 9V betweem LED and Transistor if everything is off. (...) A: Now i had success . It works. (...) I have allready done (...) (16 years ago, 29-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: RCX Serial Hardware Hack
|
|
Dear Matthew (...) A: Now it works with 4800 baud via bluetoothconnection . There was a couple of Problems. 1) At first i tried with the USB Tower but i coult only swith to 4800 bauds but there is no possibilty to change parity. 2) With the serial (...) (16 years ago, 29-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: RCX Serial Hardware Hack
|
|
"Claude Baumann" <cbaumann@ci.educ.lu> wrote in message news:K1E031.y4@lugnet.com... (...) I was able to retrieve it from archive.org - (URL) . (16 years ago, 28-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: RCX Serial Hardware Hack
|
|
(...) The carrier should be quiet in any case, because it disturbs the TX signal. (...) We tried this,but it didn't work. Why, because the transistor will drain some current, if the emitter has positive voltage and the base goes low. If the carrier (...) (16 years ago, 24-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: RCX Serial Hardware Hack
|
|
Glad to hear it is working--thank you for the update. If I may ask, I have a few questions-- * So if I understand these posts correctly, 4800 baud now works with the IR connection and not just with the hardware hack? *A couple posts from Dick Swan (...) (16 years ago, 24-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Success
|
|
Hi I have implemented the stuff // and set the port6<7> pin LOW. Now the upper PNP transistor isn't conducting anymore. Now TX and RX works Here are the program #include <lnp.h> #include <conio.h> #include <string.h> #include <lnp-logical.h> (...) (16 years ago, 20-May-08, to lugnet.robotics.rcx.legos)
|
| |
| | RCX Serial Hardware Hack
|
|
Hi As allready described in a other thread i have build a bluetoothconnection between pc and the RCX. There is one thing that the serial bluetooth is only available to tx/rx with a minimum from 4800 baud. At first i compiled brickos 0.9.0 with (...) (16 years ago, 20-May-08, to lugnet.robotics.rcx.legos)
|
